# sonarr_user: The user account used to run the sonarr daemon. # sonarr_enable: Set to YES to enable sonarr # Add the following lines to /etc/rc.conf.local or /etc/rc.conf Iocage exec sonarr mkdir /usr/local/etc/rc.dĬreate an rc file for radarr using your favorite editor at /mnt/iocage/jails/sonarr/root/usr/local/etc/rc.d/sonarr Iocage exec sonarr chown -R sonarr:sonarr /usr/local/share/NzbDrone /config Iocage exec sonarr "pw user add sonarr -c sonarr -u 351 -d /nonexistent -s /usr/bin/nologin" Iocage exec sonarr "tar -xzvf /usr/local/share/ -C /usr/local/share" Iocage exec sonarr "fetch -o /usr/local/share" Iocage exec sonarr ln -s /usr/local/bin/mono /usr/bin/mono Iocage fstab -a sonarr /mnt/tank1/video /mnt/video nullfs rw 0 0 Iocage fstab -a sonarr /mnt/tank1/torrents /mnt/torrents nullfs rw 0 0 Iocage fstab -a sonarr /mnt/tank1/apps/sonarr /config nullfs rw 0 0 Iocage exec sonarr mkdir -p /mnt/torrents Iocage create -n "sonarr" -p /tmp/pkg.json -r 11.2-RELEASE ip4_addr="vnet0|/" defaultrouter="" vnet="on" allow_raw_sockets="1" boot="on" Personally I mount the video filesystem as readonly inside the plex jail as I don't need to be able to delete media from inside plex as it is managed through other applications.Įcho '' > /tmp/pkg.json There are 2 sets of directions below based on if you require the plexpass version or not. On the iocage create command for each jail you MUST replace, with the correct values for your setup. If you find an issue with anything please make a post in the discussion thread for this resource.įor any jail below that has commands for iocage all commands should be run from the FreeNAS host. If anyone would like to see any changes let me know and I'll be happy to make them. Having the apps dataset and datasets under it made for easy snapshots of just the application config data and easy reinstalls of jails as to import data you would just need to mount the /config directory back into the new jail. I highly recommend reading this post to get a better idea on the numerous ways permissions can be done in jails to best fit your needs. This setup assumes you have a video dataset, a torrent dataset and apps dataset that has a dataset under it for each application's configuration files owned by the user that it will run as.ĭetermining the best choice for permissions for the video and torrents dataset is up to you to decide based on your setup. Most of these apps have their own forums, github repos, etc, where you can get help for each application on its own. This should help guide you to getting these apps installed however I don't have specifics on settings for each as it may vary based on your usage requirements. I figured I'd try to give back to the community a bit and share the steps for each application. When I did that I made detailed notes on how to setup each application's base install from scratch. I decided I'd migrate all of my applications back to Jails as I had them before Corral as I found them easier to manage and less resource intensive on the system. I found coming back to FreeNAS 11 some of the applications such as Transmission and Plex began to choke and lockup with the same datasets shared under NFS in Docker containers running under Rancher. While these applications worked well in Corral as docker containers with datasets shared via 9PFS. Like a number of people who may be in the same case I was in, I had gone to Corral for Docker Support. Please post in the thread so other people also assist. I try to check this thread about every 2 weeks but I will not respond to PMs for support.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |